Überblick
Meter Mode, MultiBias Mode and Calibration Mode as standard. Graph Mode is an option. UI operation interface is very simple. |
Saturation I(Sat) testing can be done using curve sweeping or using MultiBias fast test mode. |
Single trigger can produce both AC parameter and DC Resistance measurements displayed at the same time. |
Bias Status displays the working indicators of each 3265B bias source. |
Open/Short Circuit Trims, HF Compensation and Load Compensation in Boost/Normal mode, with comprehensive correction to ensure accuracy and stability. |
Field upgradeable software. Technical support available which is easy to follow, fast and convenient. Made in the UK and fast local service. |
WK5400 is the test system controller. The DC Bias Current source WK3265B machines are connected to the Bias Adapter of the 5400 directly with a dedicated wiring system. This makes it is easier to set up and maintain the system. |
Hauptmerkmal
- Designed for high current inductance testing systems.
- External DC bias current source up to 250A/1MHz or 300A/500kHz using 10 or 12 x 3265B DC Bias Units.
- Three modes of operation with independent calibrations to cover all test requirements.
- High Test Speed.
- Basic Accuracy: 0.05%
- Measurement Frequency: 10Hz~10MHz
- AC signal source: 5Vrms/200mArms. Step size < 1% of setting.
- Rdc measurements with 10uΩ resolution and drive levels up to 5V/200mA.
- Allows up to 4 different parameters to be measured, each at up to 3 different spot frequencies at the same time, totalling 12 measurement results.
- Automatic level control (ALC) maintains constant voltage or constant current at Device Under Test.
- Two settings for source resistance: 25Ω and 50Ω.
- Fixture Calibration only needed once. Does not need to be repeated if the fixture is not changed.
- Data logger firmware option /D allows measurement and results storage in real time.
- Accurate and stable testing down to pico Henry inductance level.
- Accurate testing below 100mV AC Drive Level.
- Design allows accurate testing at any testing frequency point.
- Best in Class correlation between Boost Mode and Normal Mode measurements.
- Multi-point Multi Bias with ΔL, high-speed testing
- Diagnostic Status Page indicates status of each 3265 DC Bias Unit connected in the system.
- Remote control via GPIB, LAN and USB interfaces.
- Energy-saving smart switching mode: When operating in Standalone Mode, the 3265B bias source units automatically shut down.
- Made in the UK and serviced globally.
Technische Daten
Function |
Parameter |
5400L5 |
5400L8 |
5400L10 |
---|---|---|---|---|
Measurement Frequency |
Minimum Frequency |
10Hz |
||
Maximum Frequency |
5MHz |
8MHz |
10MHz |
|
Frequency Resolution |
≦1mHz |
|||
AC Drive |
AC Voltage Range |
10mV~5Vrms |
||
AC Voltage Resolution |
<1% of setting |
|||
AC Current Range |
200uA~200mArms |
|||
AC Current Resolution |
<1% of setting |
|||
Automatic Level Control(ALC) |
ON or OFF Maintains constant voltage or constant current at the Device Under Test |
|||
Source Resistance |
Normal Mode : 50Ω ; Boost Mode : 25Ω |
|||
Basic Accuracy |
0.05% |
|||
DC Resistance(Rdc) |
DC Voltage Range |
10mV~5V |
||
DC Voltage Resolution |
1mV |
|||
DC Resistance Resolution |
10uΩ |
|||
Built-in DC Bias |
Maximum current |
Reserved temporarily |
||
External DC bias |
Maximum voltage |
Reserved temporarily |
||
External DC Bias Current using 3265B or 3265BQ* DC Bias Units |
Maximum Current and Frequency |
300A at 500kHz 250A at 1MHz 50A at 3MHz* |
||
DC Bias Current Resolution |
25mA |
Option
Order Code |
Item |
Firmware: |
|
1J5400OPG |
Analysis Function (Graphs) |
1J5400OPD |
Data Logging. Measurement and results storing in real time |
Internal Hardware: |
|
1J5400DCBIASKIT |
One interface board and cables to control 6 x 3265B DC Bias Units |
/5B1 |
Bin Handler: Non-isolated 5V signals |
/5B2 |
Bin Handler: Isolated 24V signals |
/5B3 |
Bin Handler: Universal optical coupling card |
External Hardware: |
|
1J1041 |
300A High current two-wire DIP fixture |
1J1031 |
High current two-wire SMD adaptor for 1J1041 fixture |
1J1054 |
1054 DIP fixture replacement (for 1054 supplied as standard with 5400). |